How To Install Memory In Mac Mini

Introduction

Learn how to upgrade or supervene upon the memory in your 2022 Mac mini with this RAM replacement guide. The mini tin can support upwardly to 64 GB of RAM, using any combination of viii GB, sixteen GB, or 32 GB DDR4-2666 SODIMM RAM modules.

Video Overview

• Power off and unplug your Mac mini before you begin.

• Use an opening tool to pry the bottom encompass up off of the Mac mini.







• Lift and remove the lesser embrace.

• To reinstall the encompass:

• Align it carefully so that the words "Mac mini" can be read when the ports are facing you lot.

• And so, press down on the comprehend to snap its three hidden clips into place.

• Remove six TR6 Torx security screws securing the antenna plate, of the post-obit lengths:

• Three 4.1 mm shoulder screws

• Three ane.viii mm screws

• Throughout this repair, keep rail of each screw and make sure it goes back exactly where information technology came from to avert damaging your Mac.

• Exercise non completely remove the antenna plate; it is still continued to the Mac mini by an antenna cablevision.

• With the Mac mini's ports facing you, carefully elevator the antenna plate and slide it near an inch to the right.

• Use a T6 Torx driver to remove the ii.8 mm spiral securing the antenna cable to the Mac mini's logic lath.

• The antenna cable connector and socket are fragile.

• Use the signal of a spudger or fine tweezers to gently pry the antenna cable connector straight up off its socket on the logic board.

• To reconnect the cablevision, use tweezers to position information technology carefully over its socket on the logic board, and then press it straight down until it snaps into identify.

• If you demand more slack in the cable, you can temporarily pry information technology from the clips securing it to the antenna plate.

• Remove the antenna plate from the Mac mini.

• Utilise a T6 Torx commuter to remove the four 7.2 mm screws securing the fan:

• Two screws securing the fan to the logic board

• Two screws with rubber shoulders securing the fan to the exhaust vent

• Rubber grommets secure these screws to the fan, so they may not come out completely. Merely make sure they are fully loosened.

• Don't try to remove the fan completely in this step—but lift it so you tin access the cable underneath.

• Lift the fan from the flat border where information technology meets the exhaust vent, beingness careful not to strain the fan cable underneath.

• Grasp the fan cable by all half-dozen wires and gently elevator to unplug it from the logic board.

• If the cablevision won't disconnect, don't forcefulness information technology, or you may pull the socket off the lath. Try holding the socket down with your thumb, then pinch the cablevision close to the socket with your index finger and gently lift.

• Remove the fan.

• Grasp the power supply cable and lift to disconnect it from the logic board, fluctuant as needed to loosen it up.

• Carefully lift the connector for the LED indicator low-cal straight up to disconnect it from its socket on the logic lath.

• Have care not to pry under the socket, or y'all may break it off the lath.

• Use a T10 Torx driver to remove the two vii.5 mm screws securing the logic board.

• In this stride, you'll push button the logic board gratuitous from the clips holding information technology to the frame. Push but where directed or you may harm the frail cooling fins.

• Place a thumb at each end of the frazzle vent, over the fan screw holes.

• Push button firmly in the direction of the ports until the logic lath unclips and begins to slide out of the Mac mini.

• Slide the logic lath out of the case.

• When reinstalling the logic board, make sure to hold the thin LED indicator light cable out of the way so it doesn't get damaged.

• Apply a T5 Torx commuter to remove the four 2.8 mm screws securing the RAM shield.

• Lift the RAM shield and slide it off of the RAM assembly.

• Two clips secure each RAM module in identify, one on each side. Using your fingers, spread the clips abroad from the RAM module.

• When released, the RAM modules will pop up at a slight angle.

• Slide each RAM module straight out to remove it.

• When handling the RAM modules, touch merely the outside edges. Take intendance not to bear on the gold-colored contact points forth the bottom edge.

• To install new RAM modules:

• Make sure the module is oriented correctly and the notch on the bottom is aligned, and then slide information technology in at about the same angle every bit you lot took information technology out. Press evenly until the gold contacts are no longer visible.

• Repeat for the 2d module.

• Finally, press the top edge of each RAM module to swing information technology down toward the logic board until the retaining clips on each side snap into place.

• If the safety guards interfere with the clips, spread the rubber guards abroad from the RAM with one hand and use the other to angle the RAM modules into place. And so, release the guards.

• Bank check the clips and make sure both modules are fully seated and secure.

Embed this guide

Choose a size and re-create the code below to embed this guide as a pocket-sized widget on your site / forum.

Preview

Source: https://www.ifixit.com/Guide/Mac+mini+Late+2018+Memory+%28RAM%29+Replacement/115309

Posted by: smithdesichall74.blogspot.com

Share this post